- XRACER F303V.1 CLEANFLIGHT FIRMWARE SERIAL
- XRACER F303V.1 CLEANFLIGHT FIRMWARE DRIVERS
- XRACER F303V.1 CLEANFLIGHT FIRMWARE DRIVER
- XRACER F303V.1 CLEANFLIGHT FIRMWARE SOFTWARE
Is STM bootloader mode), but I dont know what is happening. If I short the pads and power on I have the blue LED off (I supposse this Shorting the pads, but no success anyway. I am trying with CF and STM flash loader, shorting and not Latest CF version I've tried (been away for a while) did support USB. Version, so OP GCS still recognizes the board upon boot iirc. If you want flashing via OP, you need to get the correct bootloader Hex is flashed, you can unsolder and flash via Configurator from now on. Soldering the pads is the only way that (reliably) works for me. shuffleznl commented on September 2, 2015 Please veryfy the boot mode configuration and the flash protcion status.", Should I solder the pads?įrom cleanflight. I get in STM flash loader " No response from the target, the Boot loader can not be startted. If I short the pads and power on I have the blue LED off -and green one on- (I supposse this is STM bootloader mode), but I dont know what is happening. The only way I have some success is flashing a.
Tried with two boards and two diferent PCs. I am trying with CF and STM flash loader, shorting and not shorting the pads, but no success anyway. But after that no you just plug in the FTDI and flash it with CF Google App.įrom cleanflight. I din't remember if the FIRST time I had to jump the bootloader or not. it is how I flash CC3D HEX files with no problem.
hex files into CC3D with FTDI and NO shorting SBL pads.įrom cleanflight. Thx.ĮDIT: from here it seems is possible to flash. hex files to test 1.10 and Fixed wing development.Ĭan I do this through USB & chrome configurator or do I need to use FTDI and disassemble the CC3D board and short some pads inside? To use FTDI is not a problem, but to dissassemble the board each time I have to flash it would be annoying. I get "No response from bootloader" message in Chrome conf. Tried from Chrome but it didnt work, so I flashed through OP. I did with OpenPilot because USB is the easy way. The board had been flashed previously with OPenPilot GCS (.bin files 1.8.0 and 1.9.0). hex files through USB & Chrome configurator, so I have tried with no success.įrom cleanflight. What I am not sure is if I could flash in my CC3D.
XRACER F303V.1 CLEANFLIGHT FIRMWARE SOFTWARE
sppnk commented on September 1, I don't know if you are right, but I have flashed some versions of CF (.bin file) with OpenPilot GCS software throught USB port.
XRACER F303V.1 CLEANFLIGHT FIRMWARE SERIAL
That is currently not possible, you need a separate USB to Serial adapter connected to USART1 (Main Port).Īlso your CC3D board has flashed initially at least once with Cleanflight using means described in the Manual ( ) before you can use the Configurator-GUI to update the firmware.įrom cleanflight. pulsar256 commented on August 15, If I am reading this correctly, you are trying to flash the CC3D by using the CC3D's USB Port.
XRACER F303V.1 CLEANFLIGHT FIRMWARE DRIVER
I load CPdriver, window find my CC3D as Coptercontrol, so Driver look ok,ĬOM 6 appear when i plug usb so look fine alsoįrom cleanflight. 11:23:43 - Serial port successfully closed " 11:23:43 - No configuration received within 10 seconds, communication failed "Serial port successfully opened with ID: 19 Sorry, but still cannot flash, always same We flashed firmware another way and it worked.įrom cleanflight. Could not flash firmware on CC3D through USB, no matter if those pins are connected or not. No cigar on firmware update!įrom cleanflight. The blue light goes on but it never connects. Sorry for rezzing and old thread, but I'm having an issue where it says "No response from bootloader" no matter what I do. VirtualEnder commented on February 6, 2015 by using boot pins on a bricked stm32.įrom cleanflight. you need to put the device into bootloader mode manually if you enable no reboot sequence - e.g. The configurator normally sends the reboot sequence to get into bootloader mode. With "No reboot" selected: STM32 - Contacting bootloader - Operation timed out. Tried it today (with your compiled Hex), worked now WITHOUT "No reboot sequence". I get the same problem with 'failed to open serial port' like this even when flashing baseflight on some of my boards.įrom cleanflight. I guess this is a configurator bug, not a cleanflight bug, please report your findings to ctn, here: Observe that blue light goes on solid indicating firmware flasher put cleanflight in bootloader mode.Īt this point i got 'failed to open serial port'
then wait for com port to show up in the list on the configurator page, then try flashing it.įrom cleanflight. then start configurator, then plug in usb->uart->cc3d. I find that quitting chrome + configurator completely, disconnect cc3d or other board.
XRACER F303V.1 CLEANFLIGHT FIRMWARE DRIVERS
I've found the chrome serial drivers to be somewhat flakey with some of the boards i have. Comments (21) hydra commented on August 8, 2014